C.A.T4™ and Genny4™

Follow

C.A.T4™ and Genny4™

 

C.A.T4™ and Genny4™.png

 

 

C.A.T4 Model Types

 

  C.A.T4 C.A.T4+ eC.A.T4 eC.A.T4+ gC.A.T4 gC.A.T4+
Avoidance Mode™ mceclip1.png

 mceclip0.png

mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png
Genny™ signal locate mceclip2.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png
Power signal locate mceclip3.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png
Radio signal locate mceclip4.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png
Small Diameter Locate Frequency mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png

eCert™

mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png
Dynamic Overload Protection mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png mceclip0.png
Depth Estimation   mceclip0.png   mceclip0.png   mceclip0.png
StrikeAlert™ mceclip0.png mceclip1.png mceclip2.png mceclip2.png mceclip2.png mceclip0.png mceclip0.png
Data acquisition  mceclip1.png     mceclip0.png mceclip0.png mceclip0.png mceclip0.png
Service due indicator  mceclip2.png     mceclip0.png mceclip0.png mceclip0.png mceclip0.png
SWING™ warning  mceclip3.png     mceclip0.png mceclip0.png mceclip0.png mceclip0.png
CALSafe™ mceclip4.png     mceclip2.png mceclip2.png mceclip0.png mceclip0.png
Bluetooth®  mceclip5.png         mceclip0.png mceclip0.png
GPS/GNSS mceclip6.png         mceclip0.png mceclip0.png

mceclip0.png   Standard    mceclip2.png Option

 

 

Network Rail Approval   

  Network Rail logo

C.A.T4, eC.A.T4 and Genny4 are approved for use on UK railway infrastructure for which Network Rail is the Infrastructure Manager. Visit www.radiodetection.com or download Network Rail's Certificate of Acceptance PA05/05450.

 

 

ALWAYS DIG WITH CAUTION

Warning icon.pngRisk of property damage, death, or serious injury may result if buried pipes, and cables are not properly located before digging.

Warning icon.pngRead and follow all instructions and warnings in the owner’s guide before using the C.A.T4 and Genny4.

Warning icon.pngRegularly check your C.A.T4 and Genny4, in all modes, over a cable which gives a response you are familiar with.

Warning icon.pngSome power cables DO NOT radiate detectable power signals.

Warning icon.pngPower and Radio signals may not be present. It is advisable to use the Genny4 whenever searching for pipes and cables.

Warning icon.pngDo not use the C.A.T4+/eC.A.T4+/gC.A.T4+ depth estimation function to decide if mechanical digging over a buried conductor is appropriate.

Warning icon.pngStrikeAlert ™ may not activate even if a live power cable is present.

Warning icon.pngThe presence of ‘StrikeAlert Activated’ or ‘CALSafe Enabled’ labels do not guarantee that the relevant feature is activated.

Warning icon.pngKeep mobile phones away from cable and pipe locators when in operation. Minimum distance 60cm/24" recommended.

Warning icon.pngThe C.A.T4 cannot indicate whether a signal comes from a single conductor or from several cables or pipes bundled or buried in close proximity to each other.

Warning icon.pngCall your local support number (available from: www.radiodetection.com) for questions regarding the proper use, maintenance, and repair of the C.A.T4 and Genny4.

Warning icon.pngIt is recommended that the C.A.T4 and Genny4 are serviced at least once a year and have their calibration validated using Radiodetection approved test equipment. Radiodetection will accept no responsibility for repairs carried out by unauthorized repairers.

Warning icon.pngEven if using a C.A.T4 and Genny4, ALWAYS DIG WITH CAUTION. 

 

 

 

Share this Article

Was this article helpful?
0 out of 0 found this helpful

Comments