Depth and current readingsFollow
The RD7200 locator provides automatic depth of buried cables, pipes and sondes and when the locator is correctly orientated above the target line or sonde.
Current readings are also displayed simultaneously if the locator is orientated correctly (feature not available in sonde or passive frequency modes).
Depth and current readings are automatically displayed simultaneously, but if the locator is not correctly orientated neither reading will be displayed.
Depth range and accuracy vary depending on the makeup and type of target utility (e.g. cable, pipe or sonde), its depth and external environmental factors like electromagnetic noise, ground conditions and interference.
WARNING! The accuracy of depth measurement is subject to a number of factors and is meant as a guide only. Never use the depth measurement to define mechanical digging depths. Always follow local safe digging guidelines.
The depth measurement is to the center of the pipe, cable or sonde. The best readings are typically detected from ‘active’ signals output by a transmitter rather than from passive sources.
The RD7200 locator is capable of determining cable depth when locating some passive power signals. However passive signals on lines are less suited for measuring depth because accuracy can be compromized by interference- e.g due to the passive signal being present on more than one line.
WARNING! Do not make depth measurements near bends or tees in the line. Go at least 5m (16ft) from a bend for best accuracy.
TruDepth for buried conductors or sondes
TruDepth and Compass
It is important to note that the RD7200 locator will only display depth and current when the locator is correctly orientated above the target line, cable or sonde. To ensure the locator is correctly orientated, use the Compass feature.
When locating lines, make sure the Compass display is in the North / South orientation position.
When locating sondes, make sure the Compass display is in the East / West orientation.
Taking a depth reading
To minimize signal distortion, do not apply the signal by induction. If Direct Connection or signal clamping is not possible, place the transmitter in induction at least 15m (50ft) from the point of any depth measurements.
Depth measurements may not be accurate if there is audible interference or if part of the transmitter signal has coupled to a nearby line.
Confirming the Peak position coincides with a Null position indicates that the position is suitable for making a depth estimate.
- Pinpoint the target line accurately with the locator
- Check the locator is directly over the line, the antennas are at right angles to it and the locator is vertical. Adjust the sensitivity level to bring the bar graph indication to approximately 50%
If the ground appears to radiate a strong field, perhaps near a radio station, check depth by holding the bottom of the antenna 50mm (2”) above the ground and subtract this reading from the indicated depth.
Verifying depth measurements
Check a suspect or critical depth reading by lifting the locator 50mm (2”) above the ground and repeating the measurement. If the measured depth increases by the same amount it is a good indication that the depth reading is correct.
When locating for a conductor or sonde, depth measurements should be precise to ±3% if conditions are suitable. However, you may not always know if the conditions are suitable so the following techniques should be used to check critical readings:
- Check that the route of the line is straight for at least 2 meters (6 ft) to either side of the measurement point.
- Check that the signal response is reasonably constant over the 15 meter distance to the transmitter and make depth measurements to either side of the original point.
- Check that there are no adjacent lines carrying a significant signal within 1 to 2 meters (3 to 6 ft) of the target line. This is the most common source of error of depth measurements as a strong signal coupled to an adjacent line can often introduce ± 50% error.
- Make several depth measurements at points slightly displaced from the line’s apparent position. The shallowest indication will be the most accurate and will also indicate the line’s position most accurately.
Checking depth accuracy
This paragraph describes several quick and easy ways of verifying that the depth reading on the locator when used for markers or conductors and sondes is within acceptable limits.
Refer to this if you are getting inaccurate depth readings from a cable or pipe for which you know the approximate depth. Inaccurate depth readings could be the result of the locator picking up a stronger signal such as another cable or pipe running in close parallel to the target pipe or cable.
There are two ways of checking the calibration of the locator in the field. Both methods require the use of a transmitter:
Place the transmitter on top of a non-metallic object, 18” / 500mm in height or more, on the ground and away from any buried lines. Switch the transmitter on in induction mode. Hold the locator with the blade horizontal and pointing towards the front of the transmitter and approximately five meters from the front of the transmitter.
- Switch the locator on.
- Select the same frequency as is selected on the transmitter but make sure that this frequency is in the sonde mode.
- Move the locator from left to right and when the bargraph reading is at its Peak note the depth as indicated on the locator. Measure the distance from the base of the locator to the center of the transmitter using a tape measure.
- Compare this reading with the depth reading on the locator.
The locator can be considered accurate if the difference between the depth reading on the locator and the distance measured with the tape is less than 10%.
- Apply a signal to a cable or pipe of known depth.
- Locate the cable or pipe; the locator will display depth on the LCD automatically.
- Compare the depth reading on the locator with the actual depth.
NOTE: The accuracy of depth measurement is subject to a number of factors and is meant as a guide only. Exercise caution when performing any excavation.
Identifying a utility using current measurements
Measuring current value on a line helps confirm the identity of the line and may provide information about the condition of cable insulation or pipe coating.
About current measurements
The transmitter applies a signal or current onto a target line. The current decreases in strength as the distance from the transmitter increases. This rate of decrease depends on the type of line and on soil conditions. Regardless of the type of line and the frequency being used the rate of decrease should be regular with no sudden drops or changes. Any sudden or abrupt current change indicates that the line or its condition has changed.
In congested areas, where there is more than one line, the locator may sometimes detect a stronger signal from an adjacent line to which the signal has coupled or shares common grounding because it is nearer the surface. Although current measurement compensates for depth, signal response will be less as the depth increases.
The line with the highest current measurement, rather than the line giving the strongest response, is the target line to which the transmitter signal has been connected.
Measuring current provides useful information about the position of bends and intersections. Measuring current after a tee will indicate the main line that pulls more current along its greater length.
Taking current readings
Applying a transmitter signal
The transmitter signal can be connected, clamped or induced to the target line in the same way as the signal for line tracing is applied.
WARNING! Direct Connection to live conductors is POTENTIALLY LETHAL. Direct Connections to live conductors should be attempted by fully qualified personnel only using the relevant products that allow connections to energized lines.
Signal current measurements
Pinpoint the line and confirm the accuracy of the Peak pinpoint with null arrows. Check the locator is directly over the line, with the antennas at right angles to it and vertical.
The locator will automatically estimate and display depth on the LCD.
A signal coupled to a nearby line may distort the accuracy of the measurement. If the accuracy of the reading is suspect, sweep the area to check if other nearby lines are radiating the signal. If other signals are causing interference, it may be necessary to make the current measurement at another point along the line.
Both antennas are needed to make a current measurement and locator accessory antennas such as a normal clamp or stethoscope cannot be used. Because current measurement is a function of depth, it is only available in active locating modes.
Current readings using transmitter signals